Long-term effect of firing protocols on surface roughness and flexural strength of lithium disilicate glass-ceramic

Abstract This study evaluated the effect of different firing protocols on the surface roughness and flexural strength of CAD/CAM lithium disilicate glass-ceramic (LD) after aging methods. Forty-two LD bars of 16 x 4 x 2 mm (IPS e-max CAD, Ivoclar) were randomly separated into two groups according to firing protocols: Single firing-Staining, glazing, and crystallization in a single step; Multiple firings-Crystallization+First staining+Firing+Second staining+Firing+Glazing+Firing. After protocols, initial surface roughness readings were taken (Surfcorder SE1700, Kosakalab). Samples were then randomly separated into three groups (n=7) according to the aging methods they were submitted: Thermomechanical cycling (TMC, ER System, Erios, 1,200,000 cycles, 0.3 MPa, 2 Hz and 5°C/37°C/55°C, 30 s swell time); Simulated toothbrushing (STB, Pepsodent, MAVTEC, 73,000 cycles), and Control (no aging). Final surface roughness readings were done, and samples were submitted to a three-point bending test (OM100, Odeme Dental Research) and fractographic analysis by scanning electron microscopy (EVO-MA10, ZEISS). Data were analyzed (2-way ANOVA, (α=.05). There was no difference (p>.05) in the flexural strength between the firing protocols, regardless of the aging method. STB decreased the flexural strength of samples submitted to multiple firings, different from control (p<.05). Without aging (Control), before TMC, and after STB, LD had lower surface roughness when submitted to multiple firings than to single firing (p<.05). The firing protocols did not affect the flexural strength or the surface roughness of the lithium disilicate glass-ceramic, even after aging. However, toothbrushing negatively affected the flexural strength and smoothed the surface of the ceramic submitted to multiple firings.

Resumo Este estudo avaliou o efeito de diferentes protocolos de queima na rugosidade de superfície e resistência à flexão de uma cerâmica vítrea de dissilicato de lítio (DL) para CAD/CAM, após métodos de envelhecimento. Quarenta e dois barras de DL (IPS e-max CAD, Ivoclar) de 16 x 4 x 2 mm foram separadas aleatoriamente em dois grupos de acordo com os protocolos de queima: Single firing-Pigmentação, glazeamento e cristalização em única etapa. Multiple firings-Cristalização+Primeira camada do pigmento+Queima+Segunda camada do pigmento+Queima+Glazeamento+Queima. Após os protocolos, foram realizadas leituras iniciais de rugosidade de superfície (Surfcorder SE1700, Kosakalab). As amostras foram então separadas aleatoriamente em três grupos (n=7) segundo o método de envelhecimento a que foram submetidas: Ciclagem termomecânica (CTM, Sistema ER, Erios, 1.200.000 ciclos, 0.3 MPa, 2 Hz e 5°C/37°C/55°C, 30 s de imersão), Escovação simulada (ES, Pepsodent, MAVTEC, 73.000 ciclos) e Controle (sem envelhecimento). Leituras finais de rugosidade foram realizadas, e as amostras foram submetidas ao ensaio de resistência à flexão em três pontos (OM100, Odeme Dental Research) e à análise fractográfica por microscopia eletrônica de varredura (EVO-MA10, ZEISS). Os dados foram analisados (ANOVA de dois fatores, (α=.05). Não houve diferença (p>.05) na resistência à flexão entre os protocolos de queima, independente do envelhecimento. ES diminuiu a resistência à flexão das amostras submetidas a multiple firings, diferente do controle (p<.05). Sem envelhecimento (Controle), antes da CTM e após ES, LD apresentou menor rugosidade de superfície quando submetido a multiple firings do que a single firing (p<.05). Os protocolos de queima não afetaram a resistência à flexão nem a rugosidade de superfície da cerâmica vítrea de dissilicato de lítio, mesmo após envelhecimento. No entanto, a escovação afetou negativamente a resistência à flexão e poliu a superfície da cerâmica submetida a multiple firings.

Cyclic fatigue resistance of three reciprocating nickel-titanium instruments with heat treatment at intrachannel temperature

Introduction: the in vitro study compared the dynamic cyclic fatigue resistance of 3 reciprocating NiTi files with heat treatment. Methods: we distributed 30 new endodontic files in three groups. The endodontic files selected for this experiment were: AF Blue R3 25/06 (AFB) (Fanta Dental, Shanghai, China), X1 Blue File 25/06 (X1B) (MK Life, Porto Alegre, RS, Brazil), and Reciproc Blue 08/25 (RB) (VDW, Munich, Germany. We measured the time to file fractureand the length of the fractured fragment. ANOVA analysis was used, followed by the Tukey test for multiple comparisons, with a significance level of 5% (P < 0,05). Results: the mean time in seconds until the file fractured was 170.7 ±15,1 for AFB files, 110,4 ±26,8 for X1B, and 163,3 ±22,9 for RB files. This difference was statistically significant when comparing X1B to AFB (p: 0,000) and X1B to RB (p: 0,000). However, there are no statistically significant differences between RB and AFB (p:0,739). Conclussions: this study found that RB and AFB files exhibit similar resistance to cyclic fatigue.

Introducción: el estudio in vitro comparó la resistencia a la fatiga cíclica dinámica de 3 limas NiTi recíprocas con tratamiento térmico. Métodos: distribuimos 30 limas endodónticas nuevas en tres grupos. Las limas endodónticas seleccionadas para este experimento fueron: AF Blue R3 25/06 (AFB) (Fanta Dental, Shanghai, China), X1 Blue File 25/06 (X1B) (MK Life, Porto Alegre, RS, Brasil), y Reciproc Blue 08/25 (RB) (VDW, Munich, Alemania. Se midió el tiempo transcurrido hasta la fractura de la lima y la longitud del fragmento fracturado. Se utilizó el análisis ANOVA, seguido de la prueba de Tukey para comparaciones múltiples, con un nivel de significación del 5% (P < 0.05). Resultados: el tiempo medio en segundos hasta la fractura de la lima fue de 170.7 ±15.1 para las limas AFB, 110.4 ±26.8 para las X1B y 163.3 ±22.9 para las RB. Esta diferencia fue estadísticamente significativa al comparar X1B con AFB (p: 0.000) y X1B con RB (p: 0.000). Sin embargo, no hay diferencias estadísticamente significativas entre RB y AFB (p:0.739). Conclusiones: en este estudio se ha comprobado que las limas RB y AFB presentan una resistencia similar a la fatiga cíclica.

Effect of Aging and Thermocycling on Flexural Strength of PEEK as a Provisional Restoration for Full Mouth Rehabilitation – An In vitro Study

Introduction: To compare the flexural strength of autopolymerizing poly methyl methacrylate resins (PMMA) resin, CAD/CAM milled PMMA and CAD/CAM milled poly ether ether ketone (PEEK) when used as provisional restorative materials for long span situations in full mouth rehabilitation after aging and thermocycling. Materials and Methods: Sixty samples (25 mm × 2 mm × 2 mm) were fabricated using autopolymerizing PMMA resin (GROUP I), CAD/CAM milled PMMA (GROUP II) and PEEK (GROUP III). The groups were subdivided into A and B and subjected to 7 days of aging and 500 cycles of thermocycling (subgroup A) and 14 days of aging and 1000 cycles of thermocycling (subgroup B), respectively, and flexural strength was evaluated using a three?point bend test. The data were analyzed with student t test and pair?wise comparison of mean values was done by ANOVA. Results: The flexural strength of PEEK subjected to 7 days of aging and 500 cycles of thermocycling (III (A) ? 6628.70 MPa) was the highest among all groups followed by PEEK subjected to 14 days of aging and 1000 cycles of thermocycling (III (B) ? 3760.50 MPa). Conclusion: The mean flexural strength of PEEK was statistically significant than the other two materials tested and hence can be recommended for use as a provisional restorative material for long span situations in full mouth rehabilitation. However, the mean flexural strength of PEEK reduced approximately by 44% when subjected to further aging

Comparison of the Flexural Strength of Four Core Built up Materials

The aim of this study is to compare the flexural strength of 4 commonly used core build up materials in clinics. Four core built up materials, a cermet cement (ketac silver), a light cure composite, conventional silver amalgam (control group) and zirconomer (zirconia reinforced GIC) were used and were divided into Group A, B and C and D respectively. The root canal of 90 extracted mandibular molars with similar anatomy and morphology were selected. Highest flexural strength was shown by Group A followed by group C, group B and then group D.

Fracture strength and failure load of CAD/CAM fabricated endocrowns performed with different designs

Aim: Endocrown restorations are commonly used to rehabilitate endodontically treated posterior teeth and their use is well-founded in these cases. However, to date, there is little scientific evidence of their behavior in anterior teeth. The aim of this in vitro study was to evaluate the compressive strength of upper central incisors teeth, restored with glass-ceramic total crowns by the conventional anatomical core technique, and compare them to teeth restored with endocrowns with and without the presence of ferrule. Methods: Thirty teeth were randomly distributed into three groups: GE2 - endocrown group with 2 mm ferrule, GE0 - endocrown group without a ferrule, and GC - conventional crown with intraradicular post group. Crowns were cemented and teeth submitted to the 45o compression test until the fracture happened. Fractured specimens were analyzed to determine the fracture pattern. Descriptive analysis of the variables was performed and one-way analysis of variance was utilized to analyze the data for significant differences at p < 0.05. Results: The results of the control group (284.5 ± 201.05N) showed the highest fracture resistance value, followed by the 2mm group (274.54 ± 199.43N) and by the 0mm group (263.81 ± 80.05N). There was no statistically significant difference between all the groups (p = 0.964). Conclusions: The absence of a cervical enamel necklace favored a debonding of the pieces and endodontically treated anterior teeth could be restored with endocrown, which could be considered a conservative and viable treatment option

Longevity of ceramic restoring materials in the confection of endocrowns restorations: an in vitro study on surface roughness and mechanical strength / Longevidade de materiais restauradores cerâmicos na confecção de restaurações endocrowns: um estudo in vitro sobre rugosidade superficial e resistência mecânica

ABSTRACT Objectives: The objective was to evaluate the longevity of ceramic restorative materials in the manufacture of endocrown restorations, through an in vitro study on surface roughness and mechanical strength. Methods: Three restorative materials were evaluated and assigned to experimental groups (n=10 disc specimens): Leucite Reinforced Ceramic, Lithium Disilicate and Nanoceramic Resin. These restorative materials were evaluated for surface before and after aging (n=02 specimens) under a stereomicroscope. The specimens were submitted to the average surface roughness test (Ra) (n=10) in a contact roughness meter before and after aging. As well as the biaxial flexural strength test (n=10), after aging, up to a test speed of 0.5 mm/min. Aging was carried out in a thermocycler, with 5,000 cycles with baths of 5 °C ± 1 ° and 55 °C ± 1 °. Fragments after fracture were observed under a stereomicroscope. The data obtained were tabulated and analyzed using the Minitab statistical program. Results: The surfaces of the specimens do not show changes between the restorative materials and also in relation to aging. For the roughness data, the restorative material factors (p=0.867) and aging (p=0.321) were not statistically significant. The DIS group presented the highest values of fracture resistance (p=0.000), in relation to the LEU and REN groups, which were statistically similar. The same statistical pattern was identified for post-fracture fragment data (p=0.030). Conclusions: The aging factors and restorative material do not interfere with the surface roughness performance. However, the mechanical performance and number of fragments after fracture is affected by the restorative material.

RESUMO Objetivos: Objetivou-se avaliar a longevidade de materiais restauradores cerâmicos na confecção de restaurações endocrowns, através de um estudo in vitro sobre rugosidade superficial e resistência mecânica. Métodos: Três materiais restauradores foram avaliados e distribuídos em grupos experimentais (n=10 espécimes em disco): Cerâmica Reforçada por Leucita, Dissilicato de Lítio e Resina Nanocerâmica. Estes materiais restauradores foram avaliados quanto a superfície antes e após ao envelhecimento (N=2 espécimes) em estereomicroscópio. Os espécimes foram submetidos ao ensaio de rugosidade superficial média (Ra) (N=10) em rugosímetro de contato antes e após o envelhecimento. Como também, ao teste de resistência à flexão biaxial (N=10), após envelhecimento, em uma velocidade de ensaio de 0,5 mm/min. O envelhecimento foi realizado uma termocicladora, sendo 5.000 ciclos com banhos de 5 °C ± 1° e 55 °C ± 1°. Os fragmentos após fratura foram observados em estereomicroscópio. Os dados obtidos foram tabulados e analisados no programa estatístico Minitab. Resultados: As superfícies dos espécimes não mostram alterações entre os materiais restauradores e também em relação ao envelhecimento. Para os dados de rugosidade, os fatores materiais restauradores (p=0,867) e envelhecimento (p=0,321) não foram estatisticamente significativos. O grupo DIS apresentou os maiores valores de resistência à fratura (p=0,000), em relação aos grupos LEU e REN que foram estatisticamente semelhantes. O mesmo padrão estatístico foi identificado para os dados de fragmentos após a fratura (p=0,030). Conclusão: Os fatores envelhecimento e material restaurador não interferem quanto a performance da rugosidade superficial. No entanto, o desempenho mecânico e número de fragmentos após a fratura é afetado pelo material restaurador.

Influence of substrate, cement and aging on the biaxial flexural strength of lithium disilicate / Influência do substrato, cimento e envelhecimento na resistência a flexão biaxial do dissilicato de lítio

Objective: To evaluate the biaxial flexural strength (BFS) of lithium disilicate (L), cemented on different substrates (epoxy resin - E and metal - M) with dual-cure resin cement (Rc) and zinc phosphate cement (Zc), not aged, thermally aged (TC) or thermo-mechanical aged (TC/MC). Material and Methods: Disks of L, E, and M were fabricated, and the cementation was performed according to the following groups: ERc (L+E+Rc); MRc (L+M+Rc); MZc (L+M+Zc); EZc (L+E+Zc). Ten samples from each described group were tested in BFS, ten more samples were subjected to TC (1×104 cycles between 5 ºC and 55 ºC water), and the last 10 samples were subjected to TC/MC (MC: 1.2×106 cycles, 50 N, 3.8 Hz). The BFS test was performed and scanning electron microscopy (SEM) was performed to evaluate the failure mode. The effect of the cementation strategy (cement/substrate) was compared in each aging method and the effect of the aging method was evaluated for each cementation strategy by one-way ANOVA and Tukey post-hoc test (α=0.05). Results: The strength values were highest to M (237.8 ~ 463.9 MPa), in comparison to the E (41.03 ~ 66.76 MPa), despite aging and luting agent. Flexural strength data decreased after TC and TC/MC in groups cemented with Zc, but was stable when cemented with Rc. SEM analysis indicated that failure origins were located at the tensile surface of the L. Conclusion: Lithium disilicate discs cemented to the metallic substrate presented the highest biaxial flexural strength. The cementation with dual-cure resin cement did not decrease BFS after aging (AU)

Objetivo: Avaliar a resistência à flexão biaxial (BFS) do dissilicato de lítio (L), cimentado sobre diferentes substratos (resina epóxi - E e metal - M) com cimento resinoso dual (Rc) e cimento de fosfato de zinco (Zc), não envelhecido, submetido ao envelhecido térmico (TC) ou ao envelhecido térmico-mecânico (TC/MC). Material e Métodos: Foram confeccionados discos de L, E e M, e a cimentação foi realizada de acordo com os seguintes grupos: ERc (L+E+Rc); MRc (L+M+Rc); MZc (L+M+Zc); EZc (L+E+Zc). Dez amostras de cada grupo descrito foram testadas em BFS, mais dez amostras foram submetidas à TC (1×104 ciclos de imersão em água entre 5 ºC e 55 ºC), e as últimas 10 amostras foram submetidas à TC/MC (MC: 1.2 ×106 ciclos, 50 N, 3.8 Hz). Foram realizados os testes de BFS e a microscopia eletrônica de varredura (MEV) para avaliar o modo de falha. O efeito da estratégia de cimentação (cimento/substrato) foi comparado em cada método de envelhecimento e o efeito do método de envelhecimento foi avaliado para cada estratégia de cimentação por ANOVA a um fator e teste post-hoc de Tukey (α=0,05). Resultados: Os valores de resistência foram maiores para M (237.8 ~ 463.9 MPa), em comparação com E (41.03 ~ 66.76 MPa), independentemente do envelhecimento e do agente cimentante utilizado. Os dados de resistência à flexão diminuíram após TC e TC/MC nos grupos cimentados com Zc, mas se mantiveram estáveis quando cimentados com Rc. A análise MEV indicou que a origem das falhas estava localizada na superfície de tração do L. Conclusão: Os discos de dissilicato de lítio cimentados ao substrato metálico apresentaram maior resistência à flexão biaxial. A cimentação com cimento resinoso dual não diminuiu o BFS após o envelhecimento (AU)

Flexural strength and Vickers hardness of milled and 3D-printed resins for provisional dental restorations

Various forms of temporary resins are offered on the market; however, the properties of temporary resins obtained by milling and 3D printing have not been fully examined. This study aimed to compare the flexural strength and Vickers hardness of milled and 3D-printed resins. Methods: Three resins were tested: Evolux PMMA (milled resin), Cosmos Temp (3D-printed resin), and Structur 2 SC (bis-acrylic resin, group control). Specimens were prepared with rectangular shapes (n = 12) for flexural strength measurements and disc shapes (n = 9) for Vickers hardness tests. Flexural strength tests were performed at a crosshead speed of 0.75 mm/min, and the Vickers hardness was measured under a load of 20 N for 10 s. The obtained data were subjected to the Kruskal­Wallis test. Results: A significant difference (p < 0.05) in flexural strength was observed among the three sample groups: Evolux PMMA (111.76 MPa), Structur 2 SC (87.34 MPa), and Cosmos Temp (56.83 MPa). No significant difference (p < 0.05) was observed between the Vickers hardness values of Structur 2 SC (33.37 VHN) and Evolux PMMA (29.11 VHN); however, both materials were statistically superior to Cosmos Temp (10.90 VHN). Conclusion: While the mechanical properties of the milled resin were superior or similar to those of the bisacrylic resin, the 3D-printed resin was statistically inferior to both the milled and bis-acrylic resins

Influence of number and position of porcelain specimens in the furnace on flexural strength and translucency

The aim of this study was to investigate the influence of the quantity and positioning of feldspathic ceramic specimens inside the furnace on their flexural strength and translucency. The tested hypotheses were that the arrangement of specimens in the furnance would not influence 1) the translucency or 2) the biaxial strength of the porcelain. Methods: Ninety porcelain specimens were made (1.2 mm thickness and 13.5 mm diameter) and assigned into two main groups (n=15): G1 group - 15 firing cycles containing only one specimen each, always at the center of the refractory; and G5 group - 15 firing cycles containing five specimen each, where one specimen was at the center of the refractory and four specimens positioned equidistantly on the periphery. The translucency test was performed using a spectrophotometer, followed by the flexural strength test, according to ISO 6872:2015. T-student test was performed for both the mechanical and optical obtained data. Results: The flexural strength of the porcelain was not affected by the positioning (center x periphery) of the specimens inside the furnace (p =0.08), but the translucency was affected (periphery > center; p =0.009). Regarding to the number of feldspathic ceramic specimens, the biaxial flexural strength was affected (p =0.025), as well as the translucency (p <0.05). Conclusion: A higher quantity of feldspathic ceramic specimens for each firing cycle decreased its biaxial flexural strength and translucency. Also, specimens positioned at the center of the refractory became less translucent than those positioned at the periphery.

Cigarette Smoking Effect on Microhardness and Flexural Properties of Denture Base Resins

ABSTRACT Objective: To identify the tobacco effect on flexural properties and the microhardness of three acrylic resins. Material and Methods: Three resins were tested: two thermo-polymerizable acrylic resins (RMB 20 and BMS 014) and one autopolymerized acrylic resin. The 3-point bending and microhardness tests were carried out with a universal tensile-compression machine and a micro-Vickers hardness tester. The acrylic resin specimens have been exposed for 21 days to cigarette smoke in a smoking room. Their mechanical strength was compared to unexposed samples. Statistical analysis was performed using the data processing software SPSS Statistics 21.0. Results: The flexural properties of the resins were affected by cigarette smoke only in the case of Major Base 20® (drop in strength with p= 0.02; 0.6; 0.7 and in elastic modulus with p= 0.86; 0.74 and 0.85 for Major Base 20®, BMS 014® and Major Repair®). The cigarette smoke affected significantly microhardness for all groups (p<0.001). Conclusion: Cigarette smoking does not affect the flexural properties of the acrylic resin (BMS 014® and Major Repair® unlike Major Base 20®), but it does reduce the microhardness.

The effect of the die material used in the indirect technique on the fracture resistance of a restored molar

Abstract The aim of this study was to evaluate the effect of different die materials used in the indirect resin composite restorative technique on the fracture resistance and failure mode of restored molars and compare it with the direct resin composite restorative technique. Two flexible die silicone materials for dental models (Die Silicone - Voco and Scan die - Yller) and a type IV dental stone material (Fujirock EP - GC) were evaluated. Sixty third molars were selected and divided into four groups: indirect resin composite restoration - Die silicone (IRCR-DS); indirect resin composite restoration - Scan die (IRCR-SD); indirect resin composite restoration - Fujirock EP (IRCR-FR), and direct resin composite restoration (DRCR). Class II MOD cavities were prepared with 5 mm of buccolingual width and depth. The specimens were restored and subjected to an axial compression load until fracture, and the data were analyzed by one-way ANOVA and Tukey's HSD test (α=.05). The fracture mode was classified into restorable and unrestorable fractures. Fracture resistance values were influenced by the die material used for the IRCR fabrication and by the restorative technique (p<.001). Fracture resistance mean values and standard deviation were: IRCR-DS: 1835.5 ± 324.0 A; IRCR-SD: 1732.5 ± 384.1 AB; IRCR-FR: 1419.3 ± 318.8 BC; and DRCR: 1100.6 ± 224.9 C. Restorable fracture was more prevalent. IRCR with flexible die casts promoted higher fracture resistance and lower prevalence of unrestorable fractures.

Effect of different materials for temporary removable partial denture: an in vitro study on surface roughness and fracture resistance / Efeito de diferentes materiais para confecção de prótese parcial removível provisória: um estudo in vitro sobre rugosidade superficial e resistência à fratura

ABSTRACT The use of removable partial dentures is considered a common and inexpensive treatment option to rehabilitate edentulous areas. The aim of this study was to evaluate the effect of different materials for provisional removable partial dentures, an in vitro study on surface roughness and fracture resistance. Thermopolymerizable acrylic resin and thermoplastic resin specimens with dimensions of 10 x 10 x 2 mm (blocks) (n=10) and with dimensions of 65 x 20 x 3 mm (bars) (n=10 were analyzed for their surface roughness (Ra) and three-point flexural strength test. All specimens were subjected to oven aging for 60 days at 37°C±0.5°C in distilled water. The statistical analysis was performed with a significance level of 5%, and the surface roughness data were submitted to the Two-way Anova statistical test (P < 0.05) and the mechanical strength data were subjected to One-way Anova statistical test (P < 0.05). For roughness, the factor resin type (P = 0.000) and the factor aging (P = 0.000) were statically significant, as well as showing interaction (P = 0.228). The Thermopolymerizable acrylic resin had the lowest mean roughness values compared to the thermoplastic resin and showed no statistical difference after aging. The same scenario was repeated for flexural strength values; Thermopolymerizable acrylic resin was statistically superior to thermoplastic resin (P = 0.000). Thermopolymerized acrylic resin showed lower surface roughness values and higher flexural strength values compared to thermoplastic resin.

RESUMO O uso de próteses parciais removíveis é considerado uma opção de tratamento comum e de baixo custo para reabilitar áreas edêntulas. O objetivo deste estudo foi avaliar o efeito de diferentes materiais para próteses parciais removíveis provisórias, um estudo in vitro sobre rugosidade superficial e resistência à fratura. Espécimes de resina acrílica termopolimerizável e de resina termoplástica com dimensões de 10 x 10 x 2 mm (blocos) (n = 10) e de 65 x 20 x 3 mm (barras) (n = 10) foram analisados em rugosidade superficial média (Ra) e teste de resistência à flexão de três pontos. Todos os espécimes foram submetidos ao envelhecimento em estufa por 60 dias a 37 ° C ± 0,5 ° C em água destilada. A análise estatística se deu com nível de significância de 5%, e os dados de rugosidade superficial foram submetidos ao teste estatístico Anova dois fatores (P <0,05) e os dados de resistência mecânica foram submetidos ao teste estatístico Anova um fator (P <0,05). Para rugosidade, o fator tipo resina (P = 0,000) e o fator envelhecimento (P = 0,000) foram estatisticamente significantes, além de apresentar interação (P = 0,228). A resina acrílica termopolimerizável apresentou menores valores médios de rugosidade em relação à resina termoplástica e não apresentou diferença estatística após envelhecimento. O mesmo cenário foi repetido para valores de resistência à flexão; a resina acrílica termopolimerizável foi estatisticamente superior à resina termoplástica (P = 0,000). A resina acrílica termopolimerizada apresentou menores valores de rugosidade superficial e maiores valores de resistência à flexão em relação à resina termoplástica.

Influence of diameter on mechanical behavior of morse taper narrow implants

Dental implants could give back function, esthetics and quality of life to patients. The correct choice of the implant, especially in borderline cases, is essential for a satisfactory result. Aim: Thus, the objective of this study was to evaluate the mechanical behavior of Morse taper implants with two different prosthetic interfaces. Methods: Twenty self-locking Morse taper implants, 2.9 mm in diameter (FAC), and 20 Morse taper implants, 3.5 mm in diameter (CM) were divided into two groups (n=10), and submitted to strength to failure test, optical microscopic evaluation of fracture, metallographic analysis of the alloy, finite element analysis (FEA) and strain gauge test. A Student's t test (α = 0.05) was made for a statistical analysis. Results: For the strength to failure test, a statistically difference was observed (p <0.001) between FAC (225.0 ± 19.8 N) and CM (397.3 ± 12.5 N). The optical microscopic evaluation demonstrated a fracture pattern that corroborated with FEA ́s results. The metallographic analysis determined that the implants of the FAC group have titanium-aluminum-vanadium alloy in their composition. In the strain gauge test, there was no statistical difference (p = 0.833) between CM (1064.8 ± 575.04 µS) and FAC (1002.2 ± 657.6 µS) groups. Conclusion: Based on the results obtained in this study, ultra-narrow implants (FAC) should ideally be restricted to areas with low masticatory effort

Effect of frozen storage on preservation of a silicone-based test food material

Aim: This study aimed to evaluate the effect of frozen storage on the physical properties of a silicone-based test food material, highly used to evaluate the masticatory performance in research settings. Methods: A total of 1,666 silicone cubes of Optosil Comfort® with 5.6-mm edges were shaped and stored at -18°C. The cubes were subsequently tested for flexural strength (maximum force, displacement, stress, and strain) before breaking (n = 136), changes in weight and size (n = 170), and masticatory performance (n = 1360) at eight timepoints: immediately after cube preparation (baseline, no freezing), and 1, 2, 3 and 4 weeks, and 2, 4 and 6 months after frozen storage. The cubes were thawed 8 h before each assessment. Results: The maximum force, stress, maximum displacement, and deformation values for the cubes were not affected by freezing (P > 0.05). At all of the time points, the cubes exhibited similar weight (P = 0.366) and size (identical values). The masticatory performance for the cubes also showed no differences from baseline through 6 months (P = 0.061). Conclusion: Freezing Optosil Comfort® silicone cubes did not alter the physical and mechanical properties of the material, being suitable to optimize the assessment of masticatory parameters for research purposes

Repair Adhesive Strength of Conventional and Bulk Fill Resins Using Different Bonding Techniques / Resistência Adesiva de Reparo em Resinas Compostas Convencionais e 'Bulk-Fill' Utilizando Diferentes Técnicas de Adesão

This research aimed to evaluate the bond strength by micro tensile strength (µTBS), elastic modulus (EM) and flexural strength (FS) by the three-point test using three types of composite resins: Charisma Diamond, Filtek Z350 and Tetric N-Ceram Bulk Fill; and three adhesion techniques: adhesive, silane, silane and adhesive. The combinations of each resin with the adhesive technique resulted in nine groups (n = 12). Initially, with the composites, EM and FS tests were performed. Sequentially, each fragment was repaired with the different adhesive systems. All samples were subjected to µTBS testing on a universal assay machine. Data were subjected to the normality test and the parametric ANOVA test. Charisma resin showed the highest values in EM and RF compared to the other composite resins (p <0.05). The highest µTBS value was for silane + adhesive repaired Charisma resin. The lowest µTBS values were in Bulk Fill resin, regardless of adhesive system. The EM and FS results showed that Filtek Z350 resins had the best results, while bulk fill resins had lower results. It was concluded that Charisma and Filtek Z350 resins presented better results. However, in the bulk fill group, the lowest mean values of µTBS, FS and EM were obtained, as well as the lowest value in EM. (AU)

Esta pesquisa teve como objetivo avaliar a resistência de união (RU) por resistência à microtração, módulo de elasticidade (ME) e resistência à flexão (RF) pelo teste de três pontos, utilizando três tipos de resinas compostas: Charisma Diamond, Filtek Z350 e Tetric N-Ceram Bulk Fill; e três técnicas de adesão: adesivo, silano, silano e adesivo. As combinações de cada resina com a técnica adesiva resultaram nove grupos (n = 12). Inicialmente, com os compósitos foram realizados testes de ME e RF. Sequencialmente, cada fragmento foi reparado com os diferentes sistemas adesivos. Todas as amostras foram submetidas ao teste de RU por microtração em uma máquina de ensaio universal. Os dados foram submetidos ao teste de normalidade e ao teste paramétrico ANOVA. A resina Charisma apresentou os maiores valores no ME e RF em relação às demais resinas compostas (p <0,05). O maior valor de RU foi para a resina Charisma reparada com silano + adesivo. Os menores valores de RU foram na resina Bulk Fill, independentemente do sistema adesivo. Os resultados no ME e RF mostraram que as resinas Filtek Z350 obtiveram os melhores resultados, enquanto as resinas bulk fill obtiveram resultados inferiores. Conclui-se que as resinas Charisma e Filtek Z350 apresentaram melhores resultados. Entretanto, no grupo de bulk fill obteve-se as menores médias de RU, RF e ME, bem como o menor valor no ME. (AU)

Changes in the flexor and extensor muscles at different speeds / Mudanças nos músculos flexor e extensor a diferentes velocidades / Cambios en los músculos flexor y extensor a diferentes velocidades

ABSTRACT Introduction: Centrifugal strength is an important element for strength quality. Developing muscle centrifugal strength can effectively increase the stability of lower limbs and reduce the risk of injury. Objective: To explore the characteristics of contractile force of flexor ahods in strength training and rehabilitation training, and the extensor muscles of the knee joint in athletes with different speeds of centripetal force. Methods: The knee joint muscle group of 8 first-level male high jumpers and 8 second-level male high jumpers were tested by isokinetic centrifugal contraction; the angular test velocity was 60 °/s, 120 °/s, 240 °/s, and the indexes included peak torque, relative peak torque (peak torque/body weight), and the peak torque flexural extension ratio. Results: With the centrifugal contraction of the knee joint muscle group (P < 0.05), the second-level high jumpers should increase the ability of the knee flexor muscle group of the take-off leg. In the case of constant velocity centrifugal contraction (P < 0.01), taking off time must be reduced, that is, taking off speed must be accelerated. Conclusions: The difference in the knee joint muscle isokinetic test results is one of the reasons for the difference in knee joint flexor and extensor muscle contractility under the different speed forces of high jumpers. Level of evidence II; Therapeutic studies - investigation of treatment results.

RESUMO Introdução: A força centrífuga é um elemento importante na qualidade de força. O desenvolvimento da força centrífuga muscular pode, efetivamente, aumentar a estabilidade dos membros inferiores e reduzir o risco de lesões. Objetivo: Explorar as características da força contrátil do músculo flexor no treinamento de força e de reabilitação, e os músculos extensores da junta do joelho em atletas com diferentes velocidades de força centrípeta. Métodos: O grupo muscular da articulação do joelho de oito saltadores de primeiro escalão do sexo masculino, e oito saltadores de segundo escalão do sexo masculino foi testado por contração centrífuga isocinética. A velocidade de teste angular foi de 60 °/s, 120 °/s, 240 °/s, e os índices incluíram torque de pico, torque de pico relativo (torque de pico/peso corporal) e a razão extensão-flexão de torque de pico. Resultados: Na contração centrífuga do grupo muscular da articulação do joelho (P < 0,05), os saltadores de segundo escalão devem aumentar a habilidade do grupo muscular flexor do joelho da perna de arranque. No caso da contração centrífuga de velocidade constante (P < 0,01), o tempo de arranque deve ser reduzido, ou seja, a velocidade de arranque deve ser acelerada. Conclusões: A diferença nos resultados dos testes isocinéticos do músculo da junta do joelho é uma das razões para a diferença na contratilidade muscular flexor e extensor da junta do joelho sob forças de velocidade diferentes em saltadores. Nível de evidência II; Estudos terapêuticos - investigação de resultados de tratamento.

Resumen Introducción: La fuerza centrífuga es un elemento importante en la calidad de fuerza. El desarrollo de la fuerza centrífuga muscular puede efectivamente aumentar la estabilidad de los miembros inferiores y reducir el riesgo de lesiones. Objetivo: Explorar las características de la fuerza contráctil del músculo flexor en el entrenamiento de fuerza y de rehabilitación, y los músculos extensores de la articulación de la rodilla en atletas con diferentes velocidades de fuerza centrípeta. Métodos: Se testó el grupo muscular de la articulación de la rodilla de 8 saltadores de primer escalafón del sexo masculino, y 8 saltadores de segundo escalafón del sexo masculino por contracción centrífuga isocinética. La velocidad de prueba angular fue de 60 °/s, 120 °/s, 240 °/s, y los índices incluyeron torque de pico, torque de pico relativo (torque de pico/peso corporal) y la razón extensión-flexión de torque de pico. Resultados: En la contracción centrífuga del grupo muscular de la articulación de la rodilla (P<0,05), los saltadores de segundo escalafón deben aumentar la habilidad del grupo muscular flexor de la rodilla de la pierna de arrancada. En el caso de la contracción centrífuga de velocidad constante (P<0,01), el tiempo de arrancada debe reducirse, o sea, la velocidad de arrancada debe acelerar. Conclusiones: La diferencia en los resultados de las pruebas isocinéticas del músculo de la articulación de la rodilla es una de las razones para la diferencia en la contractilidad muscular flexor y extensor de la articulación de la rodilla bajo fuerzas de velocidad diferentes en saltadores. Nivel de evidencia II; Estudios terapéuticos - investigación de resultados de tratamiento.

Resistencia a la fractura de coronas dentales fabricadas análogamente vs tecnología cad-cam. Estudio In vitro / Fracture resistance of analogally made dental crowns vs cad-cam technology. In vitro study

Resumen Antecedentes. La resistencia a la fractura de las coronas puede tener influencia en su ocurrencia, de acuerdo con el método de fabricación usado, ya sea análogamente o por medio de tecnología Cad-Cam. Objetivo. Comparar la resistencia a la fractura de las coronas individuales realizadas por dos métodos de fabricación, bajo diseño asistido por ordenador y fabricación computarizada (CAD-CAM) e inyectadas. Método. Estudio in vitro. Tamaño de la muestra 20 coronas en dos grupos: 10 coronas bajo tecnología CAD-CAM y 10 coronas inyectadas. Fueron sometidas a cargas compresivas en una máquina de ensayos universal, con una velocidad de 1mm/min y una carga de celda de 5kN hasta obtener la fractura máxima de estas. Los datos se analizaron estadísticamente utilizando las pruebas Shapiro Wilk, Mann Whitney p=0,05. Resultados. Las coronas fabricadas por Cad-Cam obtuvieron un mínimo de 602,5 Newton y un máximo de 1093 Newton, mientras que las coronas fabricadas análogamente obtuvieron un mínimo de 525,2 Newton y un máximo de 1773 Newton en el experimento con la máquina de ensayo universal para lograr su fractura. Se obtuvo una diferencia significativa en la prueba de resistencia a la factura entre ambos métodos de fabricación (p <0,001). Conclusión. Las coronas de Disilicato de litio Prensadas obtuvieron una mayor resistencia a la fractura que las coronas fabricadas via CAD-CAM.

Abstract Background. The fracture resistance of the crowns may have an influence on their appearance, according to the method of making them, either analogously or by means of Cad-Cam technology. Objective. To compare the resistance to the fracture of the individual crowns made by two manufacturing methods, under computer-aided design and computerized manufacturing (CAD-CAM) and injected. Methods. In vitro study. Sample size 20 crowns in two groups: 10 crowns using CAD-CAM technology and 10 crowns injected. Crowns were subjected to compressive loads in a universal testing machine, with a speed of 1mm / min and a cell load of 5kN until obtaining the maximum bill for these. Data were statistically analyzed using the Shapiro Wilk tests, Mann Whitney p = 0.05. Results. Crowns manufactured by Cad-Cam obtained a minimum of 602.5 Newton and a maximum of 1093 Newton, while the crowns manufactured analogously obtained a minimum of 525.2 Newton and a maximum of 1773 Newton in the experiment with the machine Universal test to achieve their fracture. A significant difference was obtained in the invoice resistance test between both manufacturing methods (p <0.001). Conclusion. Pressed Lithium Disilicate crowns obtained higher fracture resistance than crowns under design and manufacturing by computer (CAD-CAM).

Resistance to fracture due to cyclic fatigue of stainless steel manual files and its association to surface roughness / Resistencia a la fractura por fatiga cíclica de las limas manuales de acero inoxidable y su relación con la rugosidad superficial

ABSTRACT The aim of this study was to evaluate the possible association between the roughness of 5 brands of stainless steel endodontic files and their resistance to fracture due to cyclic fatigue. The study includedfive different brands of stainless steel endodontic files: SybroEndo Triple-Flex Files (Kerr, Glendora, USA), Ready Steel K-Flexofile (Dentsply Sirona, Ballaigues, Switzerland), Mani Flexile Files (Mani, Tochigi- Ken, Japan), FKG K-Files (FKG, La Chaux-de-Fonds, Switzerland) and Zipperer Flexicut Files (VDW, Munich, Germany). Twelve files per brand (total 60 files) were evaluated. File surface roughness over an area (Sa) was quantified using a focus variation microscope. Then the files were subject to a cyclical fatigue test to determine the number cycles to fracture due to fatigue and length of fractured fragment. Finally, fractographic analysis was performed using a scanning electron microscope. The electropolished Ready Steel K-Flexofile® files had the highest roughness according to Sa parameters, though they also had the highest resistance to fracture due to cyclic fatigue and the longest fractured fragment. Moderate positive correlation was found between fractured fragment length and roughness. The fractured surface showed characteristics of ductile fracture with cracks and plastic deformation. The electropolished stainless steel Ready Steel K-Flexofile® files werethe most resistant to fracture due to cyclic fatigue even though they had highest surface roughness.

RESUMEN El objetivo del presente estudio fue evaluar la posible asociación entre la rugosidad de 5 marcas de limas endodónticas de acero inoxidable y su resistencia a la fractura por fatiga cíclica. Se incluyeron cinco grupos diferentes de limas endo-dónticas de acero inoxidable: SybroEndo Triple-Flex Files (Kerr, Glendora, EE. UU.), Ready Steel K-Flexofile (Dentsply Sirona, Ballaigues, Suiza), Mani Flexile Files (Mani, Tochigi-Ken, Japón), FKG K-Files (FKG, La Chaux-de-Fonds, Suiza) y Zipperer Flexicut Files (VDW, Munich, Alemania); se evaluaron doce instrumentos por grupo para un total de 60 limas. Mediante un microscopio de variación focal se cuantificó la rugosidad superficial por área (Sa) de los instrumentos, posteriormente fueron sometidos a una prueba de fatiga cíclica donde se determinó el número de ciclos de fractura por fatiga y la longitud del fragmento fracturado. Finalmente, se realizó un análisis fractográfico mediante microscopía electrónica de barrido. Las limas Ready Steel K-Flexofile® con electropulido mostraron el mayor valor de rugosidad en los parámetros Sa; sin embargo, también tenían la mayor resistencia a la fractura por fatiga cíclica y la mayor longitud del fragmento fracturado del instrumento. Además, se encontró una correlación moderada positiva entre la longitud del fragmento fracturado y la rugosidad. La superficie fracturada mostró características de fractura dúctil con grietas y deformación plástica. Las limas Ready Steel K-Flexofile® fabricadas en acero inoxidable con electropulido, fueron más resistentes a la fractura por fatiga cíclica a pesar de tener la mayor rugosidad superficial.

Vantagens custo-efetivas da utilização de ureteroscópios flexíveis descartáveis em comparação com o uso de ureteroscópios flexíveis reprocessáveis / Cost-effective advantages of using disposable flexible ureteroscopes versus using reprocessable flexible ureteroscopes

Objetivo: Analisar o custo-efetividade da utilização de ureteroscópios flexíveis descartáveis em comparação com o uso de ureteroscópios flexíveis reprocessáveis. Métodos: Revisão integrativa de literatura realizada nos bancos de dados SciELO, LILACS e MEDLINE, utilizando os descritores "ureteroscopia", "resistência à flexão", "marketing", "análise de custo-benefício" e "esterilização", cujo objeto trata das vantagens custo-efetivas da utilização do ureteroscópio flexível descartável. Resultados: Trinta e cinco artigos foram encontrados, sendo quatro utilizados no estudo. Além disso, características de sete modelos de ureteroscópios flexíveis comercializados no Brasil mais conhecidos atualmente foram apresentadas. Os resultados foram baseados na análise conjunta dos artigos selecionados e características dos modelos de flexíveis apresentados e discutidos em duas categorias: a evolução dos ureteroscópios flexíveis e marketing mix ­ ureteroscópios flexíveis de uso único. Conclusão: Apesar da escassez de pesquisas que se aprofundem em custos de utilização de um ureteroscópio flexível de uso único, comparado a um reprocessável, são notórios os benefícios advindos das inovações agregadas a esses dispositivos, dando retorno positivo tanto para o profissional que faz seu uso deles quanto para o paciente, fazendo-se necessário analisar mais profundamente a possibilidade de migração da "cultura" de uso de ureteroscópios flexíveis reprocessáveis para os descartáveis

Objective: To analyze the cost-effectiveness of using disposable flexible ureteroscopes versus using reprocessable flexible ureteroscopes. Methods: Integrative literature review conducted in the SciELO, LILACS and MEDLINE databases, using the descriptors ureteroscopy, flexion resistance, marketing, cost-benefit analysis, and sterilization, whose object deals with the cost-effective advantages of using the flexible ureteroscope disposable. Results: Thirty-five articles were found and four were used in the study. In addition, characteristics of seven models of flexible ureteroscopes commercialized in Brazil, that are currently better known, were presented. The results were based on a joint analysis of the selected articles and characteristics of the flexible models presented, and discussed in two categories: the evolution of flexible ureteroscopes; and marketing mix - flexible single-use ureteroscopes. Conclusion: Despite the scarcity of research that deepens the costs of using a flexible single-use ureteroscope when compared to a reprocessable one, the benefits arising from the innovations added to these devices are notorious, giving a positive return both to the professional who uses it and to the patient, making it necessary to further analyze the possibility of migration from the "culture" of using flexible reprocessable ureteroscopes to disposable ones

Impacto dos selantes de superfície na preservação das propriedades mecânicas de polímeros de PMMA para CAD/CAM, submetidos a desafio erosivo e termociclagem / Impact of surface sealants on the preservation of mechanical properties of PMMA polymers for CAD/CAM, subjected to erosive challenge and thermocycling

A aplicação de selantes de superfície poderá ajudar na diminuição da degradação superficial dos blocos de PMMA para CAD/CAM frente aos desafios de absorção de água, variação de temperatura e desafio erosivo causada pelo suco gástrico (frequente em pacientes com refluxo gastroesofágico (DRGE) ou bulimia. Contudo, poucos estudos na área odontológica foram realizados com essas variáveis, sendo necessário o aprofundamento sobre o assunto. Diante disso, o objetivo deste estudo foi avaliar o impacto de diferentes selantes de superfície (Biscovel LV e Palaseal) na preservação das propriedades mecânicas de polímero de PMMA para CAD/CAM, submetidos a termociclagem (T1 - 5.000 ciclos, de 5 e 55oC ; T2 ­ 10.000 ciclos, de 5 e 55oC) e desafio erosivo (DE1 - imersão em HCl 5% (pH=2,0) durante 45 horas e DE2- 91 horas), por meio da rugosidade de superfície (Ra), microdureza Knoop (MK), resistência flexural (RF) e módulo de elasticidade (ME). Foram confeccionados 90 espécimes quadrados (10x10x3 mm) para as análises de Ra e MK e 180 espécimes retangulares (25x2x2mm) para as análises de RF e ME. Os espécimes foram divididos em grupos (n=10) de acordo com o tratamento de superfície e envelhecimento. Os polimentos realizados foram: PA - pontas de borracha Astropol; PA+SB - polimento com PA + aplicação de selante de superfície Biscover LV e PA+SP - polimento com PA + aplicação de selante de superfície Palaseal. As análises foram realizadas após os tratamentos de superfície e após os períodos dos envelhecimentos. Os dados obtidos foram submetidos ao ANOVA (2 fatores), teste Bonferroni (α=0,05) e a análise de regressão linear simples. Na análise de Ra, em todos os períodos de termociclagem o grupo PA obteve os maiores valores de Ra e PA+SP os menores, com diferença significativa entre eles (p< 0.05). De acordo com a análise de regressão linear, todos os grupos apresentaram tendência linear crescente. Já após DE1 e DE2 os três grupos diferiram estatisticamente entre si (p< 0.05), sendo classificados em ordem crescente de rugosidade em PA+SP < PA+SB< PA. O grupo PA+SP manteve os valores de Ra no decorrer dos períodos de análises. Para RF, ocorreu diminuição significativa dos valores de RF do grupo PA após T1 e T2, diferindo estatisticamente dos demais grupos (p< 0.05). O desafio erosivo diminuiu de forma significante (p< 0.05) os valores de RF dos grupos PA e PA+SP após DE1 e, do grupo PA+SB após DE2. Não houve diferenças significativas nas análises de MK e ME, independente dos tratamentos de superfície e envelhecimentos. Conclui-se que os selantes de superfície foram capazes de preservar a rugosidade de superfície e resistência flexural de polímero de PMMA para CAD/CAM submetidos a termociclagem ou desafio erosivo(AU)

The application of surface sealants can help to reduce the surface degradation of PMMA blocks for CAD/CAM in the face of water absorption challenges, temperature variation and erosive challenge caused by gastric juice (common in patients with gastroesophageal reflux (DRGE) or bulimia. However, few studies in the field of dentistry have been conducted with these variables, requiring a more in-depth look at the subject. Therefore, the aim of this study was to evaluate the impact of different surface sealants (Biscovel LV and Palaseal) on the preservation of mechanical properties of PMMA polymer for CAD/CAM, subjected to thermocycling (T1 - 5,000 cycles, from 5 and 55oC; T2 - 10,000 cycles, from 5 to 55oC) and erosive challenge (DE1 - immersion in 5% HCl (pH=2.0) for 45 hours and DE2-91 hours), through surface roughness (Ra), Knoop microhardness (MK), flexural strength (RF) and modulus of elasticity (ME). The Ra and MK analyzes and 180 rectangular specimens (25x2x2mm) for the RF and ME analyses. Specimens were divided into groups (n=10) according to surface treatment and aging. The polishes performed were: PA - Astropol rubber tips; PA+SB - PA polish + application of Biscover LV surface sealant and PA+SP - polish with PA + application of Palaseal surface sealant. Analyzes were performed after surface treatments and after aging periods. The data obtained were submitted to ANOVA (2 factors), Bonferroni test (α=0.05) and simple linear regression analysis. In the analysis of Ra, in all thermocycling periods, the PA group had the highest values of Ra and PA+SP the lowest, with a significant difference between them (p< 0.05). According to the linear regression analysis, all groups showed an increasing linear trend. After DE1 and DE2, the three groups differed statistically from each other (p< 0.05), being classified in ascending order of roughness in PA+SP < PA+SB < PA. The PA+SP group maintained the Ra values throughout the analysis periods. For RF, there was a significant decrease in the RF values of the PA group after T1 and T2, differing statistically from the others groups (p< 0.05). The erosive challenge significantly decreased (p< 0.05) the RF values of the PA and PA+SP groups after DE1 and of the PA+SB group after DE2. There were no significant differences in the MK and ME analyses, regardless of surface treatments and aging. It was concluded that the surface sealants were able to preserve the surface roughness and flexural strength of PMMA polymer for CAD/CAM submitted to thermocycling or erosive challenge(AU)